Learning the Basics of Plumbing for Bathtub Installation
Learning the Basics of Plumbing for Bathtub Installation
Blog Article
What are your concepts about How to Install a Bathtub?
Installing a bathtub isn't exactly rocket science, but it does require solid plumbing, carpentry, and often, tiling abilities. Replacing an old bath tub with a brand-new one is also a moderately difficult project. If the old tub is conveniently easily accessible, the job can move easily; if you need to open a wall to get rid of the old tub and also place the new bathtub, the job is much harder. In either case, the job is within a home handyman's abilities, although you will require a helper to leave the old bathtub as well as embeded in the brand-new one. Make certain you have certified yourself for the job and fit attempting it. As opposed to hiring a contractor to take control of a halfway-completed project, it is much better to consider utilizing one before you start. Chances are you may require a professional plumber to make tube links.
This article will aid you install a brand-new tub in your washroom if you have currently acquired a new tub as well as do not require to transform the setup of your previous water supply pipelines.
Your devices as well as material list should comprise the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the supply of water. After doing so, activate the taps to drain any type of water continuing to be in the system. The process of removing the existing faucets can be fairly problematic because of the limited accessibility that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a cloth ready for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been eliminated, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from transforming during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned of any old securing compound.
Prior to moving on to fit the new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipes.
If you need to fit a monobloc, then you will need reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washing machines remain in location in between the tap as well as the sink. Secure the faucet in position with the manufacturer supplied backnut. When the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical faucet adapters. The former kind must be connected to the tap finishes first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bath tub
Using the two wood boards under its feet, place the tub in the required placement. The wooden boards are useful in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four small factors.
The following objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the level and changing the feet on the tub up until the level reviews level.
To set up taps, fit the bottom of the furthest versatile tap port to the proper supply pipe by making a compression join; then do the very same for the various other tap.
Turn on the water system as well as inspect all joints as well as new pipework for leakages and also tighten them if required. Fill the bathtub as well as additionally check the overflow outlet and also the normal outlet for leakages.
Ultimately, fix the bath paneling as explained in the producer's instruction manual. Tiling and sealing around the tub must wait till the tub has been made use of a minimum of when as this will resolve it into its final position.
Getting ready for the Installation
To start with, the supporting structure supplied with the bathroom must be fitted (if called for) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps system to prevent stress on the bathtub.
Fit the versatile faucet adapters to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you make use of every one of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be suited its last position.
Tiling Around the Bath tub
In the area where the bath meets the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to crack an inflexible seal, creating the water to penetrate the wall surface in between the bathroom as well as the tiling, causing difficulties with wetness and also possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also fittings. They are offered in tubes and cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the tub with water before sealing, to enable the motion experienced when the tub is in usage. The sealer can split fairly very early if you do not take into account this movement prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently available on the market. It is a good idea to fit the ceramic tiles making use of waterproof or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was brought to that report on Installing A Bathtub through someone on a different web address. For those who liked our blog entry please remember to share it. I cherish reading our article about A Step-by-Step Guide to Installing a Bathtub.
Access top-rated emergency plumbers. Report this page